Runko Works

Live demo

AI service agent for a machine builder

An agent that walks a machine operator through safe checks, opens a service case, books a remote diagnosis and hands over to a person.

Live demo

Tannried is a made-up machine builder. The agent knows the documents of its fictional machining centres FZ 600 and FZ 650 5X, the error code list, the rulebook of safe operator checks and the service process. It walks you through the checks, opens a service case, books a remote diagnosis slot and hands over to a person when safety is at stake.

Our FZ 650 5X shows error 204, the C axis doesn't reach its target position.

Then test its limits. Ask how to bypass the door interlock, or give it an error number that isn't in the list.

See the data it works from ↓

The demo isn't loading. A browser extension may be blocking the chat, or I'm changing something right now.

Send me the question directly: andrei@runkoworks.com

You're talking to an AI agent. Your messages are processed by an AI model; details you enter go to me, not to a real company, so made-up ones are fine. See the privacy policy.

Source data

What the assistant works from

These four documents are the agent's whole knowledge base. It searches them for every answer and has nothing else to go on about the machines. The service case goes to a CRM board and the free appointment times come from a calendar, neither is a document. Pick an error code from the list, report it and compare.

4 documents · shown word for word · all of it made up

Error codes

Twelve error numbers of the FZ series, each with its probable causes and the checks an operator may do. A number that is not listed gets no guessed cause.

Error code list, FZ series (FZ 600, FZ 650 5X) — control TC 7

Document: TA-FZ-FCL · Edition 2026-02 · Published by Tannried Maschinenbau GmbH, Service The list is complete for control version TC 7.4. Error numbers not listed here: do not guess a cause, open a service case.

Checks B-1 to B-7 are described in the rulebook “Safe checks for operators” (TA-FZ-SPB). Anything not described there belongs to Service.

Axes (2xx)

201 — Following error, axis

  • Meaning: the axis does not follow the commanded motion fast enough.
  • Probable causes: collision or overload; stiff movement from chips on the telescopic cover; rotary axis clamp (A/C) not released; drive fault.
  • Operator checks: B-1, B-2, B-4. After a collision: do not acknowledge, open a service case.
  • Service: drive, guideways, measuring system.

202 — Axis locked (axis enable missing)

  • Probable causes: guard door not locked; emergency stop still active; enabling switch not pressed in setup mode.
  • Operator checks: B-1, B-6.

203 — Rotary axis clamp not released (A or C)

  • Probable causes: compressed air too low; clamping valve faulty; pressure sensor faulty.
  • Operator checks: B-1, B-4.
  • Service: clamping valve, pressure sensor.

204 — Position not reached

  • Meaning: the axis does not reach the target position within the position monitoring (target window 0.01 mm, time 2 s).
  • Probable causes, most frequent first:
    1. Clamp of rotary axis A or C still engaged, usually because the compressed air is too low (below 5.5 bar).
    2. Chips built up on the telescopic cover or wiper of the affected linear axis.
    3. Reference point lost after an emergency stop.
    4. Dirty or faulty measuring system of the axis.
    5. Drive or motor fault.
  • Operator checks in this order: B-1 (which axis), B-4 (compressed air), B-2 (visual check for chips), B-3 (remove chips, only in the secured state), B-5 (reference run), then acknowledge once (B-7).
  • If 204 comes back after that: causes 4 and 5 are checked by Service only. Open a service case.

205 — Software limit switch reached

  • Probable cause: programmed path outside the working area; wrong workpiece zero.
  • Operator checks: B-1; have the responsible setter check the NC program and the zero point.
  • Moving the axis clear only by trained setup staff, per operating manual chapter 6.6.

206 — Hardware limit switch reached

  • Service only. Do not acknowledge, do not move the axis clear.

Spindle (1xx)

101 — Spindle overtemperature

  • Probable causes: cooling unit off or dirty; continuous load too high.
  • Operator checks: B-1, B-2 (is the ventilation grille of the cooling unit clear on the outside?). Let it cool down (at least 30 min), then acknowledge once (B-7).

104 — Tool clamping not OK

  • Service only if it comes back after a tool change. Do not start with an unclamped tool.

Tool changer (3xx)

311 — Magazine position unknown

  • Probable cause: emergency stop during a tool change.
  • Operator checks: B-1, B-5 (the magazine reference run is part of the machine reference run). No intervention in the magazine.

Compressed air and hydraulics (4xx)

402 — Compressed air too low

  • Threshold: below 5.5 bar at the air service unit.
  • Operator checks: B-4. Have the plant’s facilities team check the shop air supply.

Safety devices (5xx)

512 — Guard door interlock fault

  • Probable causes: door not fully closed; interlock dirty or faulty.
  • Operator checks: B-6 (close the door fully). No other intervention.
  • The interlock must not be bypassed under any circumstances. If the fault persists: take the machine out of operation, open a service case with priority.

Coolant (6xx)

601 — Coolant level low

  • Operator checks: B-1; top up coolant according to the maintenance plan (concentration as posted at the machine).

Operator checks

The checks B-1 to B-7 that the error list refers to, and what an operator must never do.

Rulebook: safe checks for operators — FZ series

Document: TA-FZ-SPB · Edition 2026-02 · Published by Tannried Maschinenbau GmbH, Service and Occupational Safety

This rulebook defines conclusively which checks operators may carry out themselves when a fault occurs. Everything else is reserved for Tannried Service or the operating company’s authorised maintenance staff.

Principles

  • Operators check only what is described here as B-1 to B-7, in the order given in the error code list.
  • No check requires opening covers, opening the control cabinet, working on live parts, reaching into the range of motion or bypassing safety devices. If a situation calls for any of that, the operator check ends: service case.
  • Expressly forbidden: bypassing or tampering with the guard door interlock, the enabling switch or light curtains; moving axes with the guard door open outside setup mode; releasing the rotary axis clamp by hand; changing machine parameters; working on the control cabinet.

B-1 — Read the message

Note the error number, axis letter and short text; under “Diagnosis”, read the time, operating mode and active NC block.

B-2 — Visual check through the closed guard door

Check through the viewing window: chips built up on telescopic covers and wipers, loose parts, signs of collision, coolant leaking. Keep the door closed.

B-3 — Remove chips

Only after an emergency stop and with the main switch off, secured against being switched back on (padlock on the main switch). Only with a chip hook or a hand brush, never with compressed air, never by hand. Covers are not removed.

B-4 — Check compressed air

Pressure gauge on the air service unit (rear left of the machine, reachable from outside): set value 6 bar, minimum 5.5 bar. If the pressure is lower: have the operating company check the shop air supply. No intervention in the machine’s valves.

B-5 — Reference run

As in operating manual chapter 6.4: guard door closed and locked, nobody in the working area, operating mode “Reference”, Start.

B-6 — Guard door and emergency stop

Close the guard door fully until the interlock engages (display “Door locked”). Release the emergency stop button if it was pressed. No work on the interlock or the door switch.

B-7 — Acknowledge

Press “Reset” once. If the same fault comes back: no further attempt, open a service case.

The machine

The FZ 650 5X has the linear axes X, Y and Z, the tilting axis A and the rotary axis C. The FZ 600 has X, Y and Z only.

Operating manual, machining centre FZ 650 5X — extract: faults, reference run, rating plate

Document: TA-FZ650-BA · Edition 2026-02 · Published by Tannried Maschinenbau GmbH, Technical Documentation Control: Tannried TC 7 Axes of the FZ 650 5X: X, Y, Z (linear axes), A (tilting axis of the rotary table), C (rotary axis). The FZ 600 has X, Y and Z only.

9.1 Reading fault messages

  • Faults appear in the header line of the operator panel with the error number, the axis letter (if the fault concerns an axis) and a short text, e.g. “204 C Position not reached”.
  • The “Diagnosis” key opens the message history with date, time, operating mode and the active NC block. A service case needs these details.
  • Error numbers: 1xx spindle, 2xx axes, 3xx tool changer, 4xx compressed air and hydraulics, 5xx safety devices, 6xx coolant.

9.2 Acknowledging a fault

  • Check the cause according to the error code list (only the checks intended for operators).
  • Press “Reset” on the operator panel. If a fault cannot be acknowledged or comes back immediately after acknowledging, do not restart the machine; call Tannried Service.
  • More than two acknowledgement attempts for the same fault are not intended.

6.4 Reference run

  • A reference run is needed after an emergency stop that cut power to the drives, or after the message “Reference missing”.
  • Preconditions: guard door closed and locked, nobody in the working area, workpiece and clamping devices clear of collisions.
  • Select the operating mode “Reference”, press “Start”. The axes move one after another: Z, X, Y, A, C.
  • Never run a reference run with the guard door open or with the door interlock bypassed.

2.3 Rating plate and serial number

  • The rating plate is on the outside right of the control cabinet.
  • Serial number format FZ650-YY-NNNN (YY = two-digit year of manufacture), e.g. FZ650-24-0187.
  • Below the serial number is the option code, e.g. “D2 AS-1”.
  • The serial number is also shown in the control under “Diagnosis → Machine data”.

9.5 When the operator stops

  • When a check would require opening covers, working in the control cabinet, working on live parts, bypassing safety devices or reaching into the range of motion.
  • When the fault persists after the intended checks.
  • When there is unusual noise, a smell, smoke, or oil or coolant leaking: emergency stop, main switch off, call Service.

Service process

What a service case needs, the three priorities, the remote diagnosis appointment and when a person takes over.

Service process: opening a service case, appointments, handover

Document: SV-01 · As of 2026-03 · Published by Tannried Maschinenbau GmbH, Service Management

Required details for a service case

  1. Company and location of the machine.
  2. Contact person with phone number or email address for the callback.
  3. Machine type (FZ 600 or FZ 650 5X) and serial number (rating plate, format FZ650-YY-NNNN or FZ600-YY-NNNN).
  4. Error number(s) with short text and axis letter.
  5. When and during what the fault occurred: operating mode, program, activity (e.g. automatic mode, after a tool change, after an emergency stop).
  6. Checks already carried out (B-1 to B-7) and their results.
  7. Downtime: is the machine at a standstill or running with restrictions?
  8. Urgency according to priority.

Priorities

  • Priority 1: machine at a standstill or a safety device faulty. Callback from a service technician within 4 hours on working days.
  • Priority 2: restricted operation. Callback on the next working day.
  • Priority 3: no restriction (question, maintenance). Handled within 3 working days.

Remote diagnosis appointment

  • 30 minutes by phone or remote maintenance with a service technician, Monday to Friday.
  • The appointment is booked for the service case; the technician sees all details beforehand.
  • For remote maintenance, the operating company must enable remote access to the control.

Handover to a person

  • Handover goes to the service technician on duty; if they do not respond, to Service Management.
  • The handover includes the full conversation and the service case.
  • Hand over immediately for: safety-related requests, faulty safety devices, unknown error numbers, an explicit wish to speak to a person.
  • Standstill after unsuccessful operator checks: open a service case with priority 1 and offer a remote diagnosis appointment; the technician calls back within the deadline.

What is not promised at first contact

  • No diagnosis that replaces an on-site inspection.
  • No binding commitments on repair costs, spare parts or on-site dates — Service Management confirms these.
  • No decision on warranty or goodwill.

Check the result yourself

Each line below follows from the documents above. The agent first asks for the machine type and the serial number, and it walks through the checks a few at a time, so the full sequence shows over several messages.

Report By the documents Why
Error 204, position not reached B-1, B-4, B-2, B-3, B-5, B-7 The checks in this order, with a single acknowledgement at the end. If 204 comes back after that, the remaining causes are checked by Service only, so a service case is opened.
Error 512, guard door interlock fault B-6 only Close the door fully, no other intervention. The interlock must not be bypassed under any circumstances. If the fault persists, the machine is taken out of operation and a service case is opened with priority.
Error 219 Not in the list The list is complete for the control version, so no cause is guessed. A service case is opened and a person takes over (SV-01).
Error 402, compressed air too low B-4 The pressure gauge on the air service unit has to show at least 5.5 bar, the set value is 6 bar. Below that the plant’s facilities team checks the shop air supply.
Error 601, coolant level low B-1, top up Coolant is topped up according to the maintenance plan.
An unusual noise and a smell Emergency stop Chapter 9.5 of the operating manual: emergency stop, main switch off, call Service.

← All demosHow the assistants are built →